|
Main P/N
|
End Item
|
Title
|
Aero Info P/N
|
Applicability
|
Supersedes
|
Replaces
|
| 906-10246-3 |
|
Loop Resistance Tester |
|
ALL |
|
|
| 5900T4 |
|
Safety Barricade |
|
777-ALL |
|
|
| A27038 |
-20 |
Breakout Box - Printed Circuit Card. Used to test printed circuit cards having common connectors.
Notes: Used with 160 pin connectors
|
27-MUL-1355 |
777-200A
777-200B
777-300
|
|
|
| A32074 |
-1 |
Breakout Box - Relay System, Air/Ground. Used for continuity and voltage check of air ground relay system. (May use TE65B40719) |
32-MUL-1367 |
777-200A
777-200B
777-300
|
|
|
| A33003 |
-359 |
Breakout Box - Multipurpose. Used for component testing of panel assemblies. |
33-MUL-1371 |
777-200A
777-200B
777-300
|
A33003-1
A33003-1
A33003-1 |
|
| A38010 |
-11 |
Test Cable - Potable Water Quantity Xmtr. Used to provide electrical access to water tank quantity transmitter for calibration. |
38-MUL-1583 |
777-200A
777-200B
777-300
|
|
A38010-1
A38010-1
A38010-1 |
| B71034 |
-29 |
Test Equipment - Engine Pressure Monitoring. Used to monitor engine pressure during Test Procedure No. 9 PW4000 (767) Test Procedure No. 12 JT9D (767) |
71-MUL-1395 |
|
|
|
| B71034 |
-40 |
Test Equipment - Engine Pressure Monitoring. Used to monitor engine pressure during Test Procedure No. 9 PW4000 (767) Test Procedure No. 12 JT9D (767) |
71-MUL-1395 |
|
|
|
| B71034 |
-48 |
Test Equipment - Engine Pressure Monitoring. Used to monitor engine pressure during Test Procedure No. 9 PW4000 (767) Test Procedure No. 12 JT9D (767)
Notes: Has longer hoses required for use on the 767-300
|
71-MUL-1395 |
|
|
B71034-13 |
| B71034 |
-63 |
Test Equipment - Engine Pressure Monitoring. Used to monitor engine pressure during Test Procedure No. 9 PW4000 (767) Test Procedure No. 12 JT9D (767)
Notes: Has longer hoses required for use on the 767-300
|
71-MUL-1395 |
|
|
|
| C34005 |
-1 |
Extended Box - Radio Altimeter Receiver
Transmitter. Used in place of Radio Altimeter (RA) Receiver - Transmitter (RT) primarily AlliedSignal Model ALA-52B RA RT. |
|
777-200A
777-200B
777-300
|
|
|
| F70328 |
-1 |
Probe - Film Resistance Measuring. Used with multimeter to measure resistance of electrical bond between conductive coating on non-conductive plastic sheet and the grounding fasteners. |
70-MUL-1601 |
777-200A
777-200B
777-300
|
|
|
| J22004 |
-1 |
Test Eqpt - Autothrottle Gearbox, Brake. Used in the run-in and Acceptance Test Procedures for Autothrottle Brake (254W4101), Rudder Control Brake (253W3349), and Autothrottle Gearbox Brake (254W140) Assemblies. The J22004-1, -54 are for 50 Hz Power Systems and the J22004-2, -55 are for 60 Hz. |
23-MUL-1344 |
777-200A
777-200B
777-300
|
|
|
| J22004 |
-2 |
Test Eqpt - Autothrottle Gearbox, Brake. Used in the run-in and Acceptance Test Procedures for Autothrottle Brake (254W4101), Rudder Control Brake (253W3349), and Autothrottle Gearbox Brake (254W140) Assemblies. The J22004-1, -54 are for 50 Hz Power Systems and the J22004-2, -55 are for 60 Hz. |
|
777-200A
777-200B
777-300
|
|
|
| J22004 |
-2 |
Test Eqpt - Autothrottle Gearbox, Brake. Used in the run-in and Acceptance Test Procedures for Autothrottle Brake (254W4101), Rudder Control Brake (253W3349), and Autothrottle Gearbox Brake (254W140) Assemblies. The J22004-1, -54 are for 50 Hz Power Systems and the J22004-2, -55 are for 60 Hz. |
|
777-200A
777-200B
777-300
|
|
|
| J22004 |
-54 |
Test Eqpt - Autothrottle Gearbox, Brake. Used in the run-in and Acceptance Test Procedures for Autothrottle Brake (254W4101), Rudder Control Brake (253W3349), and Autothrottle Gearbox Brake (254W140) Assemblies. The J22004-1, -54 are for 50 Hz Power Systems and the J22004-2, -55 are for 60 Hz. |
|
777-200A
777-200B
777-300
|
|
|
| J22004 |
-55 |
Test Eqpt - Autothrottle Gearbox, Brake. Used in the run-in and Acceptance Test Procedures for Autothrottle Brake (254W4101), Rudder Control Brake (253W3349), and Autothrottle Gearbox Brake (254W140) Assemblies. The J22004-1, -54 are for 50 Hz Power Systems and the J22004-2, -55 are for 60 Hz. |
|
777-200A
777-200B
777-300
|
|
|
| J22004 |
-23 |
Test Eqpt - Cargo Stop/Lock Assemblies.
Functionally test the 451W1330, 451W1360, 451W460, 451W14470 Cargo Lock Assemblies. |
|
777-200A
777-200B
777-300
|
|
|
| J26002 |
-1 |
Used to monitor and troubleshoot the airplane wiring and cardfile backplane integrity by providing pin access to connectors. The -1 consists of a -4 extender card assembly and a -7 storage box assy. |
|
777-200A
777-200B
777-300
|
|
|
| J26002 |
-2 |
Used to monitor and troubleshoot the airplane wiring and cardfile backplane integrity by providing pin access to connectors. The -2 consists of a -5 extender card assembly and a -8 storage box assy.
Notes: The -2 is used on MT&D/MBC cardfile (P29) (located in the back of the closet in the flight deck).
|
|
777-200A
777-200B
777-300
|
|
|
| J26002 |
-3 |
Used to monitor and troubleshoot the airplane wiring and cardfile backplane integrity by providing pin access to connectors. The -3 consists of a -6 extender card assembly and a -9 storage box assy.
Notes: The -3 is used on the overhead panel card files (2) (located in the P61 panel area of the flight deck).
|
|
777-200A
777-200B
777-300
|
|
|
| J26003 |
-12 |
Test Box - Time Delay, Cargo Fire Extinguishing Bottle. Used to record the elapsed time between the initial and secondary squib firings of the cargo fire extinguishing bottles.
Notes: Used with J26004 Squib Test Box.
|
26-B77-1584 |
777-200A
777-200B
777-300
|
|
|
| J26004 |
-24 |
Test Equipment - Squib, Fire Extinguishing
System. Used to verify the required voltage at the appropriate squib connector upon discharge. |
26-B77-1585 |
777-200A
777-200B
777-300
|
J26004-2
J26004-2
J26004-2 |
|
| J26004 |
-25 |
Test Equipment - Squib, Fire Extinguishing
System. Used to verify the required voltage at the appropriate squib connector upon discharge. |
26-B77-1585 |
777-200A
777-200B
777-300
|
J26004-3
J26004-3
J26004-3
|
|
| J26004 |
-26 |
Test Equipment - Squib, Fire Extinguishing
System. Used to verify the required voltage at the appropriate squib connector upon discharge. |
26-B77-1585 |
777-200A
777-200B
777-300
|
J26004-4
J26004-4
J26004-4 |
|
| J26004 |
-27 |
Test Equipment - Squib, Fire Extinguishing
System. Used to verify the required voltage at the appropriate squib connector upon discharge. |
26-B77-1585 |
777-200A
777-200B
777-300
|
J26004-5
J26004-5
J26004-5 |
|
| J26004 |
-28 |
Storage Box, Test Equipment - Squib, Fire
Extinguishing System. |
26-B77-1585 |
777-200A
777-200B
777-300
|
J26004-5
J26004-5
J26004-5 |
|
| J26004 |
-43 |
Cable Assy - Squib, Fire Extinguishing System. Used to verify the required voltage at the appropriate squib connector upon discharge. |
26-B77-1585 |
777-200A
777-200B
777-300
|
J26004-5
J26004-5
J26004-5
|
|
| J26006 |
-1 |
Controller - Power Supply, E/E Cooling Fans.Used for facilitating the operation of the Electrical/Electronic Cooling Fans (Vent and Left Supply Fan) during a normal disabler test. Consists of -2 controller assy and -3 storage box. |
|
777-200A
777-200B
777-300
|
|
|
| J26007 |
-1 |
Test Box, Cargo Smoke Heater Test Plug. Used to simulate Heater Sensor Circuit and measure voltage output of the Cargo Smoke Detection System Heater Controllers. (Applicable to 777-200; 767 GMF; 747-400 All except freighters). |
|
|
|
|
| J27056 |
-1 |
Test Eqpt - Run In, Variable Drive. Used in conjunction with customer furnished component test fixtures to accomplish run-in tests. |
|
777-200A
777-200B
777-300
|
|
|
| J27056 |
-2 |
Test Eqpt - Run In, Variable Drive. Used in conjunction with customer furnished component test fixtures to accomplish run-in tests. |
|
777-200A
777-200B
777-300
|
|
|
| J27056 |
-38 |
Test Eqpt - Run In, Variable Drive. Used in conjunction with customer furnished component test fixtures to accomplish run-in tests. |
|
777-200A
777-200B
777-300
|
|
|
| J27056 |
-39 |
Test Eqpt - Run In, Variable Drive. Used in conjunction with customer furnished component test fixtures to accomplish run-in tests. |
|
777-200A
777-200B
777-300
|
|
|
| J32001 |
-46 |
Measuring Equipment - Brake Pedal. Used to measure the load applied and the angle of travel of the brake pedals. |
32-MUL-1539 |
777-200A
777-200B
777-300
|
|
J32001-43
J32001-43
J32001-43 |
| J34001 |
-17 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-18 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-19 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-20 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-23 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-24 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-25 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-26 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-27 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-28 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
|
| J34001 |
-50 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-19
J34001-19
J34001-19 |
| J34001 |
-51 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-20
J34001-20
J34001-20 |
| J34001 |
-52 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors.. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-23
J34001-23
J34001-23 |
| J34001 |
-53 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-24
J34001-24
J34001-24 |
| J34001 |
-54 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-25
J34001-25
J34001-25 |
| J34001 |
-55 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-26
J34001-26
J34001-26 |
| J34001 |
-56 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-27
J34001-27
J34001-27 |
| J34001 |
-57 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-28
J34001-28
J34001-28 |
| J34001 |
-58 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300
|
|
J34001-17
J34001-17
J34001-17 |
| J34001 |
-59 |
Breakout Box - Line Maintenance. Used to provide pin access for LRU rack connectors. |
34-B77-1586 |
777-200A
777-200B
777-300 |
|
J34001-18
J34001-18
J34001-18 |
| J52027 |
-1 |
Test Box - Connector, Squib. Used to aid in measuring continuity and battery pack voltage at the EPAS Reservoir Squib Connector (DM52109). |
|
777-200A
777-200B
777-300
|
|
|
| J52029 |
-1 |
Test Eqpt - Squib, Overwing Exit. Used to verify Squib firing current on Escape Slide, EPAS (Emergency Power Assist System). |
|
777-300
|
|
|
|
|
|
|
|
|
|
